Throttle Body For 2003-2005 Honda Accord 2003-2006 Element 2.4L LX EX DX SE

Description

REPLACING THE THROTTLE BODY ASSEMBLY
Under some circumstances, it might be necessary to remove the throttle body
assembly. Sometimes it may be to thoroughly clean the inlet and throttle blade,
but more often it will be to replace it. The procedure is pretty straightforward.
Q: How to tell if you need a new throttle body?
Throttle Body For 2003-2005 Honda Accord 2003-2006 Element 2.4L LX EX DX SE
REPLACING THE THROTTLE BODY ASSEMBLY
Under some circumstances, it might be necessary to remove the throttle body
assembly. Sometimes it may be to thoroughly clean the inlet and throttle blade,
but more often it will be to replace it. The procedure is pretty straightforward.
Q:
How to tell if you need a new throttle body?
A:
If you find that your car idles quicker than usual, that may mean that the throttle body is sticking open. If your check engine light comes on and you find that you can’t get the car to accelerate above a certain rpm, the ECU has put you in limp mode. This means that there is something wrong with the drive-by-wire system. The most dangerous indicator is if the throttle sticks while driving and you can’t get the car to stop accelerating. If that ever happens, put the car in neutral and turn the key back one click and coast to the side of the road.
REMOVAL
1. Disconnect the ground cable from battery.
2. Lift up the vehicle. Remove the under cover.
3. Remove the clip (A), and loosen the clamps (B) and (C) securing the air intake boot.
4. Remove the air intake boot from the air cleaner case (rear) and throttle body, and move the air intake boot aside so that it does not interfere with the work.
5. Disconnect the connectors (A) from the throttle position sensor.
6. Disconnect the preheater hose (B) from the throttle body.
7. Remove the throttle body from the intake manifold.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Before installing the new assembly, inspect the intake-manifold-to-throttle-body gasket for damage.  If it is damaged, it must be replaced.
If it is in good condition, it can be reused.
WARNING:
DO NOT place fingers in or around the throttle body plate. If the throttle body is energized, the throttle plate could move causing personal injury. Always disconnect the negative battery cable prior to servicing the throttle body.
CAUTION:
DO NOT move the throttle plate while power is connected to the throttle body. This may cause fault codes to set.
Q:
Is there anything that has to be done after installing the replacement throttle body?
A:
A
relearn
calibration procedure is necessary after installation of replacement throttle body
Q:
What is throttle body relearn?
A:
Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc.
R
elearn
A MECHANICALLY CONTROLLED THROTTLE
BODY
1. Remove terminals from the battery for 15 minutes.
2. Start the engine. Let it idle for 10 minutes. Remember not to switch on any additional consumers.
3. Stop the engine for about 10 seconds. Start it again.
4. Wait until the power unit warms up to the operating temperature. After that, you can start using the vehicle.
Take notice:
you might need to drive 150–200 km until the idling stabilises.
R
elearn
AN ELECTRONICALLY CONTROLLED THROTTLE
BODY
The readjustment process might vary in different vehicles. Therefore, before you start the procedure, consult the vehicle manual for the exact step sequence.
The general algorithm is as follows:
1. Study procedure and try to remember it. You’ll have to act quickly so you won’t have time to check the details.
2. Start the engine. Warm it up to the working temperature.Stop it for 10 seconds.
3. Switch on the ignition for 3 seconds.
4. Press the accelerator pedal quickly for 5 times. One depression should take one second.
5. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
6. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
7. Release the gas pedal and start the engine.
Q:
HOW TO PREVENT THE THROTTLE BODY FROM GETTING DIRTY?
A:
1. Use only high-quality fuel. Otherwise, impurities and contaminants will get inside the engine causing the rapid formation of carbon deposits on the throttle body. For the same reason, you shouldn’t neglect the fuel filter replacement. It is recommended to flush the fuel tank from time to time.
2. Replace the air filter on time. Always make sure that the intake system is air-tight. This simple check prevents unfiltered air from being sucked into the intake system in places where its components are not connected tightly.
3. Always make sure that the crankcase ventilation system is fault-free. Its malfunctions cause a fast formation of oily deposits on elements of the throttle body.
Fits the Following Vehicles:
Please check! it is the responsibility of the purchaser to verify complete fitment
2003-2005 Honda Accord LX EX DX SE 2.4L
Item Specifics
Brand :
autodayplus
Manufacturer Part Number :
ADP1047310118S
Housing Length (in) :
6-9/16
Bore Diameter :
60mm
Housing Width (in) :
7-1/8
Main Port Inside Diameter(in) :
2-3/8
Air Intake Port Maximum Diameter (in) :
2-3/4
Throttle Plate Diameter (in) :
2-3/8
Fitment Type :
Direct Replacement
Manufacturer Warranty :
1 Year
Throttle Body Actuation Type :
Electrical
Items Included :
One Complete Throttle Body w/Sensor
Terminal QTY :
3
Gaskets Included :
No
Material :
Aluminum
Condition :
New
Interchange Part Number :
E100742,TB1149,6400RAAA62
OE/OEM Part Number :
16400-RAA-A61,6E4002 67-4002,16400RAAA61
Superseded Part Number :
Throttle Body Assembly with Sensor
Weight :
3 LB
Placement on Vehicle :
Front
Mount Hole Quantity :
4
Connector Quantity :
2
Fuel System Type :
FI
Packaging Type :
Box
Modified Item :
No
Custom Bundle :
No
Non-Domestic Product :
Yes
Mounting Hardware Included :
No
Type :
Throttle Body
(
if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.
)
1. Orders processed within 24-48 hours of payment verification.
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPS First Class Package Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!lll. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
2. It is impossible to address issues if we do not know about them!1. We accept payment via PAYPAL only.
2. Payment must be made within 4 days of auction closing.
3. Total amount due includes the final auction price plus S&H(Shipping and Handling).
4. S&H will be determined based upon the SHIP TO address.PLEASE NOTE: S&H dons not include duties,local taxes.1. We accept payment via PAYPAL only.
2. Payment must be made within 4 days of auction closing.
3. Total amount due includes the final auction price plus S&H(Shipping and Handling).
4. S&H will be determined based upon the SHIP TO address.PLEASE NOTE: S&H dons not include duties,local taxes.1. We accept payment via PAYPAL only.
2. Payment must be made within 4 days of auction closing.
3. Total amount due includes the final auction price plus S&H(Shipping and Handling).
4. S&H will be determined based upon the SHIP TO address.PLEASE NOTE: S&H dons not include duties,local taxes.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Orders processed within 24 hours of payment verification.(
if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.
)
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPS First Class/UPS/Fedex... Package Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
4.
Return shipping is to be paid by the Buyer
.
1. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
2. It is impossible to address issues if we do not know about them!
1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.
(
if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.
)
4.Payment must be received within 10 days as auction ended or order might be delayed.
New List Item
20 PC Manifold Absolute Pressure MAP Sensor For Mitsubishi Lancer GTS Sedan 2.4L
USD 103.90
Fast Response Intake Air Temperature Sensor For 1986-1992 Buick Century 12102620
USD 7.99
Car Seat Covers Luxury PU Leather Fit For Nissan Pathfinder 3.5L 2017
USD 95.88
2PCS AN10 0Degree Swivel Hose End Fitting Adapter For All Oil/ Fuel/Air Line
USD 8.44
Fit for Dodge Caliber 2007-2012 Air Temperature Sensor Sender SU3229 GT7610-930
USD 18.83
Weekly Special Sell
Shop Category
Store Home
complete strut
Specific LED Package Deals
Cylinder Piston Gasket Kit
Ignition coil
Cylinder Head Gasket Sets
Towing Mirrors
Oxygen Sensor
Door Handles
Key Shell Case
Car Floor Mats
Motor Registor
Fuel Pump Assembly
Lift Supports
Wheel Spacers
Shocks Struts
CV AXLE
wheel hub bearing
wheel lug nuts
Radiator
Fender Fastener
Starter
UTV & ATV Brake System Parts
◈  Brake Shoes
▷  Brake Pads
♢  Sintered Brake Pads
♢  Kevlar Carbon Brake Pads
Regulator Rectifier
blower motor
◈  blower motor fan
suspension kit
◈  suspension kits
◈  suspension cj
◈  suspension gxy
◈  suspension fu
AC Compressor
Braking system parts
◈  Brake Rotors
◈  Brake Pads
◈  Brake Rotors and Pads
◈  Brake Pad Sensor
◈  Brake Calipers
◈  Brake Calipers & Rotors Pads
◈  Brake pads rotors & sensors
◈  Brake pads & sensors
◈  Brake Drum & Shoes
◈  Brake Drum
◈  Brake Shoes
Car Seat Cover
Air Suspensions
Nerf Bars & Running Boards
Leveling Lift Kit
◈  leveling lift kit
Alternators
Window Switch
Window Regulator
Mass Air-Flow Sensor
tie rod
Fuel Injectors
Car Cover
License Plate Frames
Car Tools
Windshield Wiper Motor
Radiator Coolant Tank
Thermostat Housing
Timing Chain Kits
Timing Belt Kits
Water Pumps
Door Lock Actuator
Power Steering Pump
Variable Timing Solenoid (VVT)
Electric Water Pump
Valve Cover
Fuel Tank Pipe
Oil Pump
Tire Pressure Sensor
Strut Tie Bar
Throttle Body
Harmonic Balancer
Oil Pan
Motorcycle Carburetor & Parts
Urea Pump
Cooling Fan
Cooling Fan Clutch
Oil Cooler
Hydraulic Lifter&Roller Lifter
Suspension+Strut+Bearing
Starter Relay Solenoid
Gas Can Spout
HVAC
ATV Rear Wheel Axle
Car Antenna
ABS Wheel Speed Sensor
DE
◈  Radlager Satz
Parking sensor
PTO Clutch
Spoilers & Wings
Tensioners
Vacuum Pump
Purge Valve
Knock Sensor
Turbocharger
Crankshaft Position Sensor
Camshaft Position Sensor
MAP Sensor
Oil Pressure Sensor
Throttle Position Sensor
Stator
idle air control valve
Running Board Motor
Transfer Case Shift Motor
Clutch Slave Cylinder
Consoles & Parts
Roof Rack
Tire Pressure Gauge
Steering Rack
Wiring Harness
Spark Plug Ignition Wire
Engine Mount
Glow Plug
Air Cleaner Filter Box
Ignition distributor
Cylinder Piston Kit
window visor
Pressure Tester Gauge
Jack Stands
C Notch & Flip Kit
Wheel Lug
Sun Visor
Trim tilt motor
ATV Brake Caliper
Car Carburetor
Horns
Heater Control Valve
Steering U-Joint
Fuel Shut Off Solenoid
Fuel Cell Tank
Height Level Sensor
Temperature Sensor
Driveshaft
Vacuum Actuator
Air Ride Suspension Valves
Rubber Seal Strip
Radiator Hose
Ballast module
Release Cable
Dipstick
Removal Open Tools
Camshaft & Crankshaft
ATV Brake Master Cylinder
Rocker Arm
Bumper
◈  Chrome Steel Bumper
◈  Complete Bumper Assembly
◈  Bumper Spacer Support Bracket
Fuel Injector Wiring Harness
4WD Actuator
Trailer Adapter
Battery Switch
Wheel Hub Bearing Knuckle
Throttle Cable Carb Bracket
Oil Filter Wrench
Oil Fuel Hose Line
Jeep
suspension 7 BIN
◈  chenjiao
◈  oukaixuan
◈  fujiali
brake Hose
LED headlight Assembly
headlight motorcycle
Foot Rest Pedals
O Rings
water Pump Impeller
Strut Mount
Wheel Stem Air Valve Cap
A/C Expansion Valve
Splash Guards & Mud Flaps
Evaporators
Heater Cores
vehicle speed sensor
RV Water Pump
Fuel Pressure Regulator
Light Bar Mount Bracket
Sensor-8
tire cover
CV axle+Brake Pads/Rotors
Steering Shaft
transmission filter
transmission kit
spindle
Steering Wheel
Steering Wheel Hub
Steering Gear Box
Hydraulic Hand Brake
snorkel air intake
CDI BOX
Proportioning Valve
Alternator Bracket Kit
Other Golf Cart Parts
Wheel Hub Centric Rings
Fender flares
Window Glass Hinge
4 pcs wheel hub bearing
brake Line Lock Kit
Hood Latch Lock
ATV Tires
jumper cable
Other Handlebars & Levers
Body Kits
dash cover
primary drive clutch
tire pressure sensor
Jack Plate
AC Compressor Control Valve+A
carburetor intake mainfold
Fuel Valve& Petcocks
Garden Water Pump
Switch Panel
air vent
Car Window Film Tint Tools
Windshields
Lower Kits & Parts
Cargo Cover
Leaf Springs
hub caps
ATV Ignition Switch
fog lights
winch
Other Motorcycle Parts
Jeep exterior
Brake Clutch Lever
Door Hinge Conversion Kits
Pillar Posts
Fuse Holder Box
Tonneau Cover
Windshield Outer Trim
Steering Knuckle
Power Brake Booster
Radiator Support
Drop Spindle Lowering Kit
Hot Stapler
leveling kit + struts shocks
Wheel Rim
Car & Truck Lighting & Lamps
◈  Exterior Lighting
◈  LED 3RD Brake Light
◈  Cab marker Roof Running light
◈  License Plate Light
◈  Headlight
◈  Instrument Panel Lights
◈  Side Marker Lights
◈  Interior Lighting
Parking Brake Actuator
Remote Control Box
Other
Hot Item
2 For Ford Explorer Focus Mustang 2002-2010 Keyless Entry Car Remote Key Fob
USD 8.99
2 For Nissan Altima 350Z 2002 2003 2004-2006 Keyless Entry Car Remote Key Fob
USD 9.99
For Ford F-150 Expedition 2004 2003 2002 2001 2000 1999 1998 1997 Ignition Coil
USD 32.99
4x Beige Inside Inner Interior Door Handle For 98-02 Toyota Corolla Chevy Prizm
USD 9.53
2 For Ford F-150 1999 2000 2001 2002 2003 2004 2005 2006 2007 Remote Car Key Fob
USD 7.99
Throttle Body For 2003-2005 Honda Accord 2003-2006 Element 2.4L LX EX DX SE
REPLACING THE THROTTLE BODY ASSEMBLY
Under some circumstances, it might be necessary to remove the throttle body
assembly. Sometimes it may be to thoroughly clean the inlet and throttle blade,
but more often it will be to replace it. The procedure is pretty straightforward.
Q:
How to tell if you need a new throttle body?
A:
If you find that your car idles quicker than usual, that may mean that the throttle body is sticking open. If your check engine light comes on and you find that you can’t get the car to accelerate above a certain rpm, the ECU has put you in limp mode. This means that there is something wrong with the drive-by-wire system. The most dangerous indicator is if the throttle sticks while driving and you can’t get the car to stop accelerating. If that ever happens, put the car in neutral and turn the key back one click and coast to the side of the road.
REMOVAL
1. Disconnect the ground cable from battery.
2. Lift up the vehicle. Remove the under cover.
3. Remove the clip (A), and loosen the clamps (B) and (C) securing the air intake boot.
4. Remove the air intake boot from the air cleaner case (rear) and throttle body, and move the air intake boot aside so that it does not interfere with the work.
5. Disconnect the connectors (A) from the throttle position sensor.
6. Disconnect the preheater hose (B) from the throttle body.
7. Remove the throttle body from the intake manifold.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Before installing the new assembly, inspect the intake-manifold-to-throttle-body gasket for damage.  If it is damaged, it must be replaced.
If it is in good condition, it can be reused.
WARNING:
DO NOT place fingers in or around the throttle body plate. If the throttle body is energized, the throttle plate could move causing personal injury. Always disconnect the negative battery cable prior to servicing the throttle body.
CAUTION:
DO NOT move the throttle plate while power is connected to the throttle body. This may cause fault codes to set.
Q:
Is there anything that has to be done after installing the replacement throttle body?
A:
A
relearn
calibration procedure is necessary after installation of replacement throttle body
Q:
What is throttle body relearn?
A:
Idle Relearn (aka throttle body relearn) is the procedure that is required to obtain the correct idle speed after replacing electronic throttle body, disconnecting a battery cable, clearing a check engine light, etc.
R
elearn
A MECHANICALLY CONTROLLED THROTTLE
BODY
1. Remove terminals from the battery for 15 minutes.
2. Start the engine. Let it idle for 10 minutes. Remember not to switch on any additional consumers.
3. Stop the engine for about 10 seconds. Start it again.
4. Wait until the power unit warms up to the operating temperature. After that, you can start using the vehicle.
Take notice:
you might need to drive 150–200 km until the idling stabilises.
R
elearn
AN ELECTRONICALLY CONTROLLED THROTTLE
BODY
The readjustment process might vary in different vehicles. Therefore, before you start the procedure, consult the vehicle manual for the exact step sequence.
The general algorithm is as follows:
1. Study procedure and try to remember it. You’ll have to act quickly so you won’t have time to check the details.
2. Start the engine. Warm it up to the working temperature.Stop it for 10 seconds.
3. Switch on the ignition for 3 seconds.
4. Press the accelerator pedal quickly for 5 times. One depression should take one second.
5. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
6. Press the gas pedal to the floor for 7 seconds. Keep it depressed until the “Check Engine” light burns steady and hold it for 3 more seconds.
7. Release the gas pedal and start the engine.
Q:
HOW TO PREVENT THE THROTTLE BODY FROM GETTING DIRTY?
A:
1. Use only high-quality fuel. Otherwise, impurities and contaminants will get inside the engine causing the rapid formation of carbon deposits on the throttle body. For the same reason, you shouldn’t neglect the fuel filter replacement. It is recommended to flush the fuel tank from time to time.
2. Replace the air filter on time. Always make sure that the intake system is air-tight. This simple check prevents unfiltered air from being sucked into the intake system in places where its components are not connected tightly.
3. Always make sure that the crankcase ventilation system is fault-free. Its malfunctions cause a fast formation of oily deposits on elements of the throttle body.
Fits the Following Vehicles:
Please check! it is the responsibility of the purchaser to verify complete fitment
2003-2005 Honda Accord LX EX DX SE 2.4L
Item Specifics
Brand :
autodayplus
Manufacturer Part Number :
ADP1047310118S
Housing Length (in) :
6-9/16
Bore Diameter :
60mm
Housing Width (in) :
7-1/8
Main Port Inside Diameter(in) :
2-3/8
Air Intake Port Maximum Diameter (in) :
2-3/4
Throttle Plate Diameter (in) :
2-3/8
Fitment Type :
Direct Replacement
Manufacturer Warranty :
1 Year
Throttle Body Actuation Type :
Electrical
Items Included :
One Complete Throttle Body w/Sensor
Terminal QTY :
3
Gaskets Included :
No
Material :
Aluminum
Condition :
New
Interchange Part Number :
E100742,TB1149,6400RAAA62
OE/OEM Part Number :
16400-RAA-A61,6E4002 67-4002,16400RAAA61
Superseded Part Number :
Throttle Body Assembly with Sensor
Weight :
3 LB
Placement on Vehicle :
Front
Mount Hole Quantity :
4
Connector Quantity :
2
Fuel System Type :
FI
Packaging Type :
Box
Modified Item :
No
Custom Bundle :
No
Non-Domestic Product :
Yes
Mounting Hardware Included :
No
Type :
Throttle Body
(
if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.
)
1. Orders processed within 24-48 hours of payment verification.
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPS First Class Package Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!lll. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
2. It is impossible to address issues if we do not know about them!1. We accept payment via PAYPAL only.
2. Payment must be made within 4 days of auction closing.
3. Total amount due includes the final auction price plus S&H(Shipping and Handling).
4. S&H will be determined based upon the SHIP TO address.PLEASE NOTE: S&H dons not include duties,local taxes.1. We accept payment via PAYPAL only.
2. Payment must be made within 4 days of auction closing.
3. Total amount due includes the final auction price plus S&H(Shipping and Handling).
4. S&H will be determined based upon the SHIP TO address.PLEASE NOTE: S&H dons not include duties,local taxes.1. We accept payment via PAYPAL only.
2. Payment must be made within 4 days of auction closing.
3. Total amount due includes the final auction price plus S&H(Shipping and Handling).
4. S&H will be determined based upon the SHIP TO address.PLEASE NOTE: S&H dons not include duties,local taxes.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
1. Orders processed within 24 hours of payment verification.(
if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.
)
2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
3. The images shown are not the actual item and are for your reference only.
4. Fast shipping:All our packages use USPS First Class/UPS/Fedex... Package Service
5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!
1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!
2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
4.
Return shipping is to be paid by the Buyer
.
1. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
2. It is impossible to address issues if we do not know about them!
1.We only accept PayPal.
2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
3.
(
if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.
)
4.Payment must be received within 10 days as auction ended or order might be delayed.
Copyright of autodayplus. All rights reserved.